Home > Can 39 T Access > Can't Access My Modem Ip Address

Can't Access My Modem Ip Address

Contents

If you can’t access 192.168.1.1 – or the IP address your router uses – here’s how to get connected. I cannot access the setup program by entering 192.168.0.1 in browser address bar. When I try to reset it (power off/on with reset button pressed for more than 30 sec.) the power light blinks but I still can't access to admin interface. ForumsJoin All FAQs → Charter Forum FAQ → 5.4 Troubleshooting Open navigator Open navigatorWhat Should my Modem Signal Levels be?How do I check the signal on my cable modem?What can I have a peek here

I only have one computer at present, but can access my modem from the internet on my phone. Highlight (but don't uncheck) Internet Protocol (TCP/IP) and click the properties button. If you set your network adapter to "Obtain an IP address automatically" in the TCP/IP properties and your PC gets an IP address it is communicating with the router. How do I solve quadratic equations when the coefficients are complex and real?

Can't Access My Modem Ip Address

Thanks again. Now I am not able to connect to my router. Can't access most websites.

I can reset my modem. 2. If it IS, then your computer's ethernet NIC is the trouble. See what you IP address is... Can't Connect To Modem Then I replaced my router to see whether I can open 192.168.1.1 And yes.

Make sure Obtain an IP address automatically is selected, and also Obtain DNS server address automatically. Can't Access Router Settings I changed my IP to my Router from 192.168.1.1 to 192.168.10.1 so my IPs show up as 192.168.10.? Stick a label on the router so you won’t forget the IP address, Wi-FI password and router username and password. this contact form if you still cannot connect to your router then open internet explorer Options > Advanced tab > click reset and follow instructions, before doing that: right click the network connection icon

Detailed Explaination Right now you actually have 3 different networks: As you can see in the image, the LAN and modem are on the same network, but separated by the router. 192.168.0.1 Refused To Connect. Helpful +30 Report anyman Jun 5, 2010 at 03:19 AM try https://192.168.1.1 man, I hope it works :) Helpful +21 Report peerData Jul 2, 2009 at 07:49 AM Yes your Gateway And try again. This is a discussion on [SOLVED] Cannot access my modem's config page.

Can't Access Router Settings

You might want to try configuring it with a static IP address in the router's subnet (DHCP might not be configured properly yet).Use a Cat5 cable to configure wireless routers - Mine are 192.168.2.1 for router and 192.168.1.1 for modem. Can't Access My Modem Ip Address Temporarily disable these to see if they are causing the problem. Can't Access Default Gateway Flag Permalink This was helpful (0) Collapse - re by Jimanyyy / November 21, 2010 7:51 AM PST In reply to: IP address . . .

I've been in the interface before and need it to port forward, obviously. http://globalcryptonews.com/can-39-t-access/can-39-t-access-certain-websites-on-any-browser.html Thank you for helping us maintain CNET's great community. After resetting your router you can follow the earlier steps to connect to the router’s management interface. Thats like asking a computer to divide by 0. 192.168.1.1 Refused To Connect

ipconfig needs to be run from a command prompt. Right-click on the Ethernet adapter and choose Properties. I'm able to get on the web and access the DD WRT UI of my router but I can't access the modem any longer. Check This Out thank you Helpful +38 Report totois 2Posts Wednesday June 9, 2010Registration date June 9, 2010 Last seen Jun 9, 2010 at 01:49 AM Very simple.

At the prompt type ipconfig and press Enter. 192.168.1.1 Took Too Long To Respond. Then scroll down the list to find Internet Protocol Version 4. XtrastorJul 3, 2012, 3:38 AM Yea I understand that but, in the first post I said that my PC was connected directly to the modem, so it would be in the

Next Step » Next Prev Can’t access 192.168.1.1 or 192.168.0.1: How to change router settings: Step-by-step guide To access your router settings you need to know its IP address, and if

Recent What internet speed is needed to watch Sling TV and Netflix ? 35. Access Point ? To fix this problem, reconnect this hardware device to the computer." It is my limited understanding that DHCP requires all three to be running.I have tried without success to fix this The 192.168.1.1 Page Isn’t Working Perform these steps: Click Start - Run type cmd - Click ok In the Command Window type ipconfig and press enter.

From there you can set the device. the only problem that I have is that any devices cant connect the wireless from the router (WPA2,WPA, WEP , Disabled).. Please go back to the Quick Installation Guide and make sure all physical connections are correct. this contact form I tried everything I found on may forums except resetting router.

I did try all the things adviced here.. Click here to Register a free account now! What should I do? Can't access your modem internal pages?

Windows is asking to "Enter Network Credentials" to access network ? The router will need to be connected to the mains and turned on in order for this to work. by anonymous - 2011-11-29 23:38 I couldn't access my route setup page right after cisco network magic was installed. by anonymous - 2013-04-23 18:25 192.168.2.1 worked fine for me!

Click on it and then click the Properties button. So if you get a IP in IPCONFIG of 192.168.2.? On the back of your router there is a small round reset button. Windows’ built-in firewall shouldn’t cause a problem.

but those who using BSNL BB or those with a telephone line must be disconnect beforehand.. I tried to find the solution on google. solved page_fault_in_nonpaged_area now can't access windows solved can't access 192.168.0.1 router page from my windows 10 PC but works fine on windows 7 laptop and mobile. solved Can't plug in my ethernet into my modem anymore??

Any ideas? :( 05-04-2011, 01:24 PM #4 joeten Microsoft-Team Manager Hardware - Team Manager Join Date: Dec 2008 Location: Glasgow Scotland Posts: 63,738 OS: win 7 pro/ultimate/xp There could also be settings within your web browser which are causing a problem, so try a different browser to eliminate this as an issue. Also, I have runn ipconfig and the ethernet adapter local area connection shows "no ip address (0.0.0.0)" Futher examination shows some sort of DHCP problem. What caused my meringue to fall after adding cocoa?

All rights reserved.